Wheels

No.9 36w rims are our choice for all-around trail riding and off-road touring. They fit a huge range of modern mountain bike tires and offer lightweight performance across the board. Available in both 27.5" and 29" sizes, these highly versatile mountain rims provide huge performance gains over aluminum rims of the same width. A perfect mix of width, weight, and stiffness, these will be right at home on almost any mountain bike in your stable. As with all rims we sell, these come with tubeless valves and tape in the box. - Designed to be used with spoke nipple washers - Recommended weight limit 240lbs

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Hope Front Axle Conversion Kits · Compatible with Pro 2 and Pro 2 Evo hubs

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.

- Light enough to take XC racing but was born from research and testing on the Enduro World Series circuit, making it a great rim for anyone looking to improve both descending and climbing - Asymmetric rim design allows for a stronger wheel while offering the easy inflation and Stan's trademark unmatched airtight seal. - 28mm internal width ideal for 2.2-2.5" tires - Light and durable 6069 aluminum with welded joint and reinforced spoke bed

Surly Rim Strips have one job and they do it well. They cover the cutouts in your rim and — if you're running a tube — they protect it from spoke heads and other sharp matter (okay, so maybe they have TWO jobs but they do them both really well.) Rim strips are crucial and should be used with all Surly rims. Ours come in an array of colors so you can really "express yourself." Surly Rim strips are available in two different materials: PVC and Nylon. PVC is great if you plan on only running tubes. However, if there's any part of you that wants to try this tubeless thing you've been hearing about, Nylon strips are just the ticket. They're thinner and offer minimal stretch so they stay put and lay nicely inside the rim to provide a secure seal. Plus, they're lighter which we all know means you'll go faster… maybe.

From the purist gravel racer to the mixed-surface fanatic, Terra CLX II provides a level of weight savings and material confidence that’s unheard of in the all-road or gravel space. This tier of weight-savings translates to rocket-like acceleration off the starting line, nimble performance in the hills, and unleashed efficiency on those loaded-down long-haul excursions. Weighing in at just 1250 grams, the Roval Terra CLX II are the lightest wheels in their class, rivaling pure climbing wheels in terms of weight and out-performing in raw toughness. We were able to get even lighter than before (50 grams lighter) by utilizing Low Flange Disc (LFD) hubs, borrowed from the Alpinist CLX II wheels. What’s being carried forward from the previous generation, is the rim. With its multiple Unbound victories, we we kept what was already class leading, and extended our lead. Because Terra CLX II is a hooked rim, you’re able to ride almost any tire and pressure. Thanks to the 25mm internal width, they work seamlessly with 28-47c tires (up to 80 PSI), giving you options to customize your setup for what’s ahead. Using Roval LFD hubs, still spinning on DT Swiss 180 hub internals, Terra CLX II continues to provide flawless ride quality. The CINC ceramic bearings inside do some serious heavy lifting when it comes to the efficiency of these wheels. Even with laundry list of demands that need to be met for the serious gravel racer, to the all-road explorer—the Roval Terra CLX II checks every box with authority. - Rim: Terra CLX Carbon Clincher, 700c, Disc Brake, Tubeless Compatible - Rim Details: 32mm Depth, 30mm External Width, 25mm Internal Width - ERD 577mm - Hub: Roval Light Hub (LF13/LF14R) Center Lock, DT Swiss 180 Ratchet EXP 36t internals (10 degs), 100x12mm & 142x12mm, Shim. RD. 11SP HG freehub - Bearing Type: DT Swiss SINC Ceramic Bearings - Spokes: DT Swiss Aerolite T-head, Front: Radial/One-cross (2:1) 21 count, DS: 278mm, NDS: 290mm, Rear: One-cross/Two-cross (2:1), DS: 290mm NDS: 288mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 28mm - 47mm - Max Pressure: 28c-32c: 80psi, 33c – 36c: 65psi, 37c- 47c: 60psi - Weight: Wheelset 1,250g, Front 570g, Rear 680g (excludes 15g, tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step, from rim layup to the last nipple turn. - Extras: Roval Rim Tape, Spare Spoke & Nipple Kit, System Weight Limit: 275lbs/125kg

WCS Zeta GX 650B TA12 Wheelset

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

Ritchey Front Hub Conversion Kits

Authentic Ritchey hub conversion kit for mountain bike hubs. - Convert 15mm (OD) alloy axle to QR9 ID - Quick release skewer not included

Authentic Ritchey hub conversion kit for mountain bike hubs. - Convert to 15mm thru-axle - End cap conversion for Vantage and Trail non 2-piece V2 hubs for 15mm thru axle

Replacement XD driver freehub body for Trail and Vantage 2-piece Ritchey hubs. - SRAM XD

Authentic service bearing kit for Ritchey mountain bike and road wheels. - Bearing service kit for Phantom Flange rear hubs Includes #6903 (x1pc) & #699 (x1pc)

Big Deal spoke nipple washers are not required for tubeless set up. When used, they eliminated the need for tubeless tape.

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

EX 1700 SPLINE wheels feature a super strong and welded 30 mm wide aluminum rim with a profile design made to withstand the hardest use of Enduro racing, while still keeping the weight low for long and demanding uphills. Laced to double butted competition straightpull spokes, the EX 1700 SPLINE wheels are built to take a beating. - Welded Aluminum rim with 30mm internal width - 350 hub with 36 point SL Ratchet system - Competition spokes and Squorx nipples - Designed for Enduro applications

Wherever the road takes you, the ERC 1400 wheels with AERO+ optimized rim profiles allow you to stay in control during your extended endurance ride. Ride longer distances effortlessly thanks to wider and more comfortable tires. Each pedal force is transferred into propulsion and speed onto the 240 DICUT Aero hub by the reliable Ratchet EXP freehub system and DT aero comp t-head spokes. Simply enjoy your ride along the way. - Fast and light, Aero-optimized wheels for those longer rides on various terrains along your route. Ride comfortably and handle your bike safely even in fast descends

Replacement axles for Manitou forks

Replacement axles for DT Swiss hubs.

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

New WCS hubs using a ratchet system freehub. - 24.8mm inner width rim with a 19.1mm height - DT Swiss Competition double butted spokes - 1840g with the included TLR rim tape

The ARC Offset rims utilize an asymmetrical design to optimize spoke tension balance, wheel durability, and wheel stiffness. Its 6069 Alloy construction provides a superior strength-to-weight ratio, significantly improving toughness. - Offset nipple bed for improved spoke tension balance and wheel strength/stiffness - Strong tire retention bead - Tubeless ready

A true bmx classic. The Hazard Lite is respected because of its strength, reliability and light weight. Often imitated but never matched in quality or durability. The Hazard Lite is the rim of choice for some of the world’s best riders. - Fully welded joint construction - Directional spoke hole drilling

After a long climb, the perfect trail lies ahead of your tires: flowy, dusty, varied, endless. Nothing holds you back from entering the All-Mountain thrills with the M 1900 Spline wheels. A rim developed with optimal balance of durability and weight offers efficient climbing characteristics as well as dent resistance on single trails. With experienced wheel building by hand, this wheel is a reliable partner to collect freewheeling moments in the mountains. - Intended use = XC and All-Mountain/Trail - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

- Mid Fat, and Fat Race are what this thing is all about - Perfect for sand, snow, trail, and everything in between - Double wall for increased stiffness and tubeless ready - 45mm width disc-only rim

Zipp's 303 S Tubeless Disc Brake wheelset provides today's cyclists the versatility they demand with the speed they crave. Expanding greatly on its heritage of conquering the Spring Classics, this 303 wheelset maintains its ideal-for-every-terrain 45mm rim depth but adds a significantly wider internal width to provide greater performance and ride quality in almost every measurable way. This wheelset is tubeless for disc-brake bikes, allowing the ability to run wide tires at lower pressures for race-ready speed on or off the pavement. The 303 S is among our lightest wheelsets, optimized for top aero performance with a 28mm tire but capable of handling gravel tires up to 50mm wide. - Wide rims optimize tire profile to allow lower tire pressure, especially with tubeless. The result is a larger contact patch for increased grip and confident cornering, descending, and handling in wet conditions. - Lower tire pressures and larger volume provides a compliant ride with fewer vibrations. - Significant watt savings when running larger tires at lower pressure. - Wide, hookless rims create a seamless transition to the tire, reducing drag. - Fastest with 28mm, but fits wide gravel tires as well - New Zipp graphics and cosmetic identity that scream speed

- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair

The SES 2.3 is purpose-built for going up. Ultra-light, respectfully aerodynamic, and optimized for tubeless tires the SES 2.3 raises the bar for performance through hilly and mountainous terrain. - Front and rear optimzed depths and shapes (27mm front, 32mm rear) - 21mm internal width is optimized for ENVE 27mm tires - Hookless tubeless rim is compatible with 25mm-32mm tires

- Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires - E-sync hubs Specs: - Wheel Tire Type: Tubeless Ready - Wheel-Brake Comp.: Disc IS 6-bolt - Rim Material: Aluminum - Spoke Type: Sapim D-Light - Valve: Presta - Rim Construction: Double wall

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools. Designed to keep you in the saddle and out of the service queue - Classic j-bend spoke interface - Steel cartridge bearings are durable

Your entire focus lies on the right line choice, the exact braking point and the spot-on steering movement. All the everyday stress fades away, you feel free and only hear the precise sound of the freehub system. The E 1900 Spline wheels were developed precisely for these freewheeling moments. A proven aluminum rim and hand-laced steel spokes provide the reliability required from an Enduro wheel. - Intended use = All-Mountain/Trail, Enduro and Freeride - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Industry Nine Hydra Classic mountain hubs are loaded with features every rider will appreciate such as revolutionary 0.52° engagement, generously low weights and an intuitive layout that can be serviced without any proprietary tools. - From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards in Asheville, NC - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - Classic j-bend spoke interface - Steel cartridge bearings are durable - Easily serviced with no proprietary tools; Designed to keep you in the saddle and out of the service queue

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools. Designed to keep you in the saddle and out of the service queue - Classic j-bend spoke interface - Steel cartridge bearings are durable

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

Shimano XT FH-M8010/M8000 Rear Hubs. - Double contact bearing seals - Super polished bearing races for low friction rolling - Shimano Quick-engagement freehub - Not compatible with Shimano 11-Speed Road cassettes - Cone bearings races ground by a Cubic Boron Nitride tool for smooth-rolling durability - Center Lock disc brakes provide reliable braking power (lockring sold separately)

SMOOTHER IS FASTER Trail riders who prize nimble handling will be blown away by Traverse SL II's category-leading control, strength-to-weight ratio, and pinch-flat resistance. LIGHTER At 1,645 grams, this is our lightest trail wheelset ever. STRONGER Front and Rear Specific Rims with carbon layups optimized for strength and weight boast 15% greater front wheel strength and 25% more rear wheel strength than the previous Traverse SL. CONTROL-BOOSTING VERTICAL COMPLIANCE 21% more vertically compliant than the previous Traverse SL (delivered through Shallow Rim Shape and front/rear specific layup) enables enhanced terrain hugging and bump-force absorbing control. TRACTION MONSTER Carefully engineered rim shape intentionally flexes for improved support and traction to boost confidence and control. TOUGH LIFE, LONG LIFE Engineered rim offset enables balanced spoke tension for improved fatigue life. Lifetime warranty on Roval Wheels when registered within the first 90 days of purchase. SAYONARA PINCH FLATS Optimized "Flat Top" bead profile requires 85% more force to pinch flat compared to a standard round bead, virtually eliminating "snake bites." AIR TIME Thank our genius engineer Chuck Teixeira for inventing the "Roval ThreadBed Valve"; a valve that threads directly into the rim eliminating compression nuts, air loss from rim flex, and makes tire set-up easier, and reduces sealant clogs. INTENDED USE Trail WEIGHT (29) 1,645g 240 EXP (with valve and tape) WHEEL SIZES: 29 2 Year "It Happens" No Fault Crash Replacement - If you damage your Roval product while riding within the first two years of ownership and it's not covered under warranty, we'll still replace or repair. USA Only and wheels must be registered. STRUCTURAL WEIGHT LIMIT (Rider & Cargo) - 125kg / 275lbs

Proterra Tough i30 wheels keep the trail in check while everything else blurs by in the periphery. Reinforced by our proven Dual I-Beam support, Proterra Tough rims feature a 30mm internal width to provide higher tire volume while also increasing sidewall support at lower pressures. High-quality EZO sealed bearings are designed to endure through seasons of aggressive riding, while a responsive 6-pawl freehub provides the snappy 3.7 degrees of engagement you demand when cranking out of corners. Choose Proterra Tough when you need a wheel that won't let you down. - 30mm inner rim width with 32 spokes laced in a 3-cross pattern - 6069 aluminum alloy rim is TCS 2.0 tubeless-ready - Sapim Secure Lock 14-gauge brass nipples provide bomber durability, while double butted 2.0/1.8/2.0mm J-bend spokes make replacement a breeze. - Tubeless tape, Solid Strip, and black alloy valves are preinstalled, making the wheels ready for tubeless tires the moment they arrive on your doorstep. The TCS 2.0 Solid Strip is a durable strip that lies beneath the tape, prevents it from sagging at the spoke holes, makes it easier to mount a tire, and protects from puncture in the case of a broken spoke. - 6-bolt rotor mounts - Top-tier EZO sealed bearings

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

The Boost 6-Bolt front is specifically for "Boost" disc spacing forks with 110x15mm "Boost" axles. Using the larger diameter hubshell bearing the Boost 6-Bolt is designed to tackle rough terrain and aggressive riding such as downhill and enduro. In an evolving landscape of axle specifications, we are confident that the "Boost" disc location is here to stay. Chris King Boost 6-Bolt front hubs are designed as precision mountain tools. We use one-piece axles to provide a stiff hub with rail accurate steering, transferring every minute adjustment you make to the trail. To thwart mud, water, and contaminants as you power through rough trails, Boost hubs have heavy-duty bearing seals and snaprings, that provide superior protection with ultra low drag. Our bearings, available in steel and ceramic, have heat-treated, surgical grade steel races that are machined simultaneously, with tools of equal wear to ensure perfectly matched inner and outer races. The quality and speed of our bearings is what sets us apart from the competition and they are what you will feel and notice on every single ride. As Chris King bearing tracks burnish they get faster with age and all our hubs and bearings are fully serviceable for years upon years of demanding use. - Steel Bearings - Engineered, manufactured and assembled in Portland, Oregon USA - King Lifetime Warranty - Wide flange placement - Fits 110x15mm Boost axles - Legendary made-in-house LD bearings - Easily serviceable with a 2.5mm hex and pick or pen knife - Completely re-buildable with our Universal Hub Service Tool - Responsibly lightweight - Ceramic bearing upgrade available - Available in 28, and 32 hole spoke count

Chris King Boost 6-Bolt 148x12 rear hubs are designed as precision mountain tools. We use one-piece solid axles to provide a stiff hub that will help your suspension perform better and drive every watt of power into the dirt. To thwart mud, water, and contaminants as you power through rough trails, Boost 6-Bolt hubs have heavy-duty bearing seals, and a threaded driveshell seal ring. Our bearings, available in steel and ceramic, have heat-treated, surgical grade steel races that are machined simultaneously, with tools of equal wear to ensure perfectly matched inner and outer races. The quality and speed of our bearings is what sets us apart from the competition and they are what you will feel and notice on every single ride. As Chris King bearing tracks burnish they get faster with age and all our hubs and bearings are fully serviceable for years upon years of demanding use. The patented Chris King RingDrive with 72-points of simultaneous-engagement will get your power to the ground fast, provide unmatched engagement, and give you that legendary Chris King angry-bee sound. - Steel Bearings - Engineered, manufactured and assembled in Portland, Oregon USA - King Lifetime Warranty - Canted flanges for stronger wheel builds - Patented RingDrive system with 72 simultaneously interfaced points of contact for unmatched hub engagement - Legendary made-in-house bearings - Come in 28h and 32h drilling - Available with Micro Spline, HG or XD driveshell. - Easily serviceable with a 2.5mm hex and pick or pen knife - Completely re-buildable with our ISO Hub Service Tool - Responsibly lightweight - Ceramic bearing upgrade available - Specifically designed for "BOOST" 148mm x 12mm axle standard

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Aluminum rear hub for bicycle - 18P DBCL 24 holes, straightpull, black. Aluminum Campagnolo freehub body, black. - Dimension: 12x142mm

Grade 10 chromium steel balls

Zipp Speed Weaponry Freehub Bodies - Material: Aluminum

- 30mm wide rim with an Enduro style layup. Designed for tires in the 2.4 to 2.7 range. - Offset rim bed for balanced spoke tension. - Tripel hub with quick 3.5 degree engagement, and super low drag. - Super strong hookless rim.

- Made start to finish in Asheville, NC - Light weight and easy to service

- 27.5"x20 KT Alloy ATB style front wheel - STW A275 silver rim with silver hub - UCP silver spokes

- 27.5"x20 MTB Formula 6 bolt disc front wheel - STW A275 silver 36h rim with black hub - UCP silver spokes

Sun Duroc 40 Disc blk 32h - -01: STW Turbo Boost 6-Bolt disc - -02: STW Turbo Boost Shimano 6-Bolt disc

The Drive Thru is a dummy hub or chain keeper that replaces your wheel while cleaning the chain. It is a fast and effective way to clean your chain between races or in your garage. It allows you to fully rotate your cranks and shift through your complete range of gears while protecting the frame. Installs simply with one hand, and is quick and easy to change between bikes. The Drive Thru is also great for packing the bike for transport. *This Drive Thru Value Meal includes three dummy axles with 1.0, 1.5 and 1.75 thread pitches and one pulley. - Value Meal includes 1.0, 1.5, and 1.75mm thread pitch dummy axles. - All Drive Thru dummy axles are 12mm in diameter. - Dummy axles are precision machined from 7075 aluminum and knurled for easy grip. - Pulleys are machined from durable Delrin. - Oil and solvent resistant O-rings - Lead-in threads designed for quick insertion into the frame - Simple, one-handed installation (no tools required)

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

Sta-Tru Double Wall Rear Wheels. - Wheel Size: 20-inch - ISO Diameter: 406 / 20-inch BMX - Valve: Schrader - Tire Type: Clincher

Sta Tru Front Wheel - Single Wall rim - Hub/Brake Compatibility: Rim Brake - Wheel Size: 18-inch - ISO Diameter: 355 / 18-inch BMX - Front Axle: 3/8-inch x 100mm - Tire Type: Clincher

The Rampage rear wheel features a sealed bearing hub, 14mm axle and a Rampage double-walled rim. - Includes Stolen PVC rim strip - Brake Compatibility: Rim Brake - Wheel Size: 20" - ISO Diameter: 406 / 20" BMX - Valve: Schrader - Tire Type: Clincher - Axle: 3/8" chromoly (Heat-treated) - Hardware: Steel (17mm wheel nuts) - Hub Shell Bearings: 6000 (x2) Verify bearing number on side of rubber seal - Spokes: 187mm (3X) Black w/ Black Brass nipples - Drilling: 36h only - Weight: 32.5 oz

The Rampage rear wheel rolls on a four-bearing sealed freecoaster hub with 14mm chromoly axle. It's hand-laced to a 36-hole Rampage double-wall rim, and features a 9T chromoly driver with 3-pawl system. - Axle: 14mm chromoly (heat-treated) - Driver: 1-pc chromoly RHD or LHD - Hardware: Steel(17mm wheel nuts) - Hub shell bearings: 6002 (x1) & 7902 (x1) verify bearing number on side of rubber seal - Drilling: 36H - Weight: 46.4-ounces